Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
Forum untuk mengobrol hal-hal bebas.
Moderators: Ryan Steele , sh00t , r12qiSonH4ji , avantgardebronze , akbarfit
marmut
New Member of Mechanic Master
Posts: 11865Joined: Wed Oct 16, 2013 6:27Location: tangerang selatan
Post by marmut Fri Oct 02, 2020 6:44
Omnibus wrote: Fri Oct 02, 2020 6:14
ball joint remover/separator mbah
keluarkan screw nya, dimasukan lagi dgn terbalik arahnya. lalu posisikan di caliper sbg penahan. trus pakai 1 keping brake pad bekas utk didorong melawan piston oleh screw tsb. brake padnya yg bagian friction material yg nempel ke piston.
difoto ya mbah kl sdh bisa. okeeee ....
nu ieu?
20201002_133802.jpg
kelamaan mbah ngeluarin screw segala, pencet pake 2 jempol lebih cepet. apalagi kalo piston imut macem avania....
You do not have the required permissions to view the files attached to this post.
marmut
New Member of Mechanic Master
Posts: 11865Joined: Wed Oct 16, 2013 6:27Location: tangerang selatan
Post by marmut Fri Oct 02, 2020 6:45
... dan 2 halaman lagi untuk masuk ke halaman 60...
indeskey
New Member of Mechanic Engineer
Posts: 887Joined: Fri Nov 23, 2018 9:27Location: Depok
Post by indeskey Fri Oct 02, 2020 7:32
marmut wrote: Fri Oct 02, 2020 6:45
... dan 2 halaman lagi untuk masuk ke halaman 60...
yang lain mana nih?
hadir mbah suhu....
yanuarra
Full Member of Mechanic Engineer
Posts: 4040Joined: Sat Dec 28, 2019 9:55Location: Jakarta
Post by yanuarra Fri Oct 02, 2020 7:46
marmut wrote: Fri Oct 02, 2020 6:45
... dan 2 halaman lagi untuk masuk ke halaman 60...
yang lain mana nih?
Hadir mbah..
Omnibus
New Member of Mechanic Master
Posts: 11781Joined: Tue Apr 08, 2008 10:12
Post by Omnibus Fri Oct 02, 2020 8:12
marmut wrote: Fri Oct 02, 2020 6:44 Omnibus wrote: Fri Oct 02, 2020 6:14
ball joint remover/separator mbah
keluarkan screw nya, dimasukan lagi dgn terbalik arahnya. lalu posisikan di caliper sbg penahan. trus pakai 1 keping brake pad bekas utk didorong melawan piston oleh screw tsb. brake padnya yg bagian friction material yg nempel ke piston.
difoto ya mbah kl sdh bisa. okeeee ....
nu ieu?
20201002_133802.jpg
kelamaan mbah ngeluarin screw segala, pencet pake 2 jempol lebih cepet. apalagi kalo piston imut macem avania....
betul yg itu! he he he
kl ketemu piston caliper yg gede boleh lah coba2 belajar dulu dr skrg. kita mau tau nih....
Omnibus
New Member of Mechanic Master
Posts: 11781Joined: Tue Apr 08, 2008 10:12
Post by Omnibus Fri Oct 02, 2020 8:21
btw
mbah marmut , minta foto kan? dapet salam dr cobek/cowet/ulekan
IMG-20201002-WA0004.jpg
IMG-20201002-WA0005.jpg
*ga beli ga perlu katanya.
You do not have the required permissions to view the files attached to this post.
marmut
New Member of Mechanic Master
Posts: 11865Joined: Wed Oct 16, 2013 6:27Location: tangerang selatan
Post by marmut Fri Oct 02, 2020 8:57
Omnibus wrote: Fri Oct 02, 2020 8:21
btw
mbah marmut , minta foto kan? dapet salam dr cobek/cowet/ulekan
IMG-20201002-WA0004.jpg
IMG-20201002-WA0005.jpg
*ga beli ga perlu katanya.
marmut
New Member of Mechanic Master
Posts: 11865Joined: Wed Oct 16, 2013 6:27Location: tangerang selatan
Post by marmut Fri Oct 02, 2020 9:03
ijinken saya mewakili saudara
jd200 yang pemalu untuk memajang salah satu koleksinya....
20201002_153956.jpg
isi dalamnya
20201002_153937.jpg
masih ada lagi solder station merk dekko, nanti kalau sudah dapat fotonya, pasti saya pajang...
saudara jack daniels ini diam-diam D.I.Y aliran garis keras, sudah berhasil bongpas dashboard LS400 dengan sukses. salut...!!!
saat saya seumur itu, nggak akan berani bongpas dashboard.
You do not have the required permissions to view the files attached to this post.
Omnibus
New Member of Mechanic Master
Posts: 11781Joined: Tue Apr 08, 2008 10:12
Post by Omnibus Fri Oct 02, 2020 9:25
widiww 1/2" dan 1/4" combo, lengkap sm mata soket busi 21 mm n 16 mm. ada bits set juga lagi.
lolos passing grade penerimaan civitas institut van asem reges dgn dekan mbah yanuarra dan rektor mbah marmut n wakil rektor mbah dohc.
.........
marmut
New Member of Mechanic Master
Posts: 11865Joined: Wed Oct 16, 2013 6:27Location: tangerang selatan
Post by marmut Fri Oct 02, 2020 9:31
ternyata saya masih menyimpan sedikit dokumentasi saat saudara jack daniels sedang beraksi dengan dekko solder station-nya,
Mr.
jd200 gabut utak atik ECU LS400,
20200116_211428.jpg
sedikit penampakan dekko di sisi kanan atas,
20200116_203320.jpg
puyeng,
20200116_140240.jpg
You do not have the required permissions to view the files attached to this post.
Dat510
New Member of Mechanic Engineer
Posts: 796Joined: Sat Jan 03, 2015 12:58
Post by Dat510 Fri Oct 02, 2020 9:34
Ikut meramaikan dalam rangka percepatan thread Hand Tools menuju Part 3.
WhatsApp Image 2020-10-02 at 4.15.36 PM(1).jpeg
WhatsApp Image 2020-10-02 at 4.15.36 PM.jpeg
Socket KTC 36 mm 6pt drive 1/2 inc. Ada yang tau buat ini mau buat ngebuka apa?
You do not have the required permissions to view the files attached to this post.
DOHC
Full Member of Mechanic Master
Posts: 27643Joined: Sat Jan 31, 2009 17:48Location: in engine bay with carbonfibre as roof
Post by DOHC Fri Oct 02, 2020 9:43
Kann sperti yg sering bilang
numpang lewat aja....
DOHC
Full Member of Mechanic Master
Posts: 27643Joined: Sat Jan 31, 2009 17:48Location: in engine bay with carbonfibre as roof
Post by DOHC Fri Oct 02, 2020 9:44
Dat510 wrote: Fri Oct 02, 2020 9:34
Ikut meramaikan dalam rangka percepatan thread Hand Tools menuju Part 3.
WhatsApp Image 2020-10-02 at 4.15.36 PM(1).jpeg
WhatsApp Image 2020-10-02 at 4.15.36 PM.jpeg
Socket KTC 36 mm 6pt drive 1/2 inc. Ada yang tau buat ini mau buat ngebuka apa?
Baut as roda
Lipindut punya kl ga salah aj 32 atau 34
numpang lewat aja....
marmut
New Member of Mechanic Master
Posts: 11865Joined: Wed Oct 16, 2013 6:27Location: tangerang selatan
Post by marmut Fri Oct 02, 2020 10:06
Dat510 wrote: Fri Oct 02, 2020 9:34
Ikut meramaikan dalam rangka percepatan thread Hand Tools menuju Part 3.
WhatsApp Image 2020-10-02 at 4.15.36 PM(1).jpeg
WhatsApp Image 2020-10-02 at 4.15.36 PM.jpeg
Socket KTC 36 mm 6pt drive 1/2 inc. Ada yang tau buat ini mau buat ngebuka apa?
widih, 36mm masih 1/2" square drive sih nekat..... biasanya paling kecil 3/4" square drive-nya.
36mm yang saya inget baut as roda belakang peugeot 505.
yanuarra
Full Member of Mechanic Engineer
Posts: 4040Joined: Sat Dec 28, 2019 9:55Location: Jakarta
Post by yanuarra Fri Oct 02, 2020 10:11
Dat510 wrote: Fri Oct 02, 2020 9:34
Ikut meramaikan dalam rangka percepatan thread Hand Tools menuju Part 3.
WhatsApp Image 2020-10-02 at 4.15.36 PM(1).jpeg
WhatsApp Image 2020-10-02 at 4.15.36 PM.jpeg
Socket KTC 36 mm 6pt drive 1/2 inc. Ada yang tau buat ini mau buat ngebuka apa?
Buat buka mur pulsator atau gearbox mesin cuci kayanya.......
marmut
New Member of Mechanic Master
Posts: 11865Joined: Wed Oct 16, 2013 6:27Location: tangerang selatan
Post by marmut Fri Oct 02, 2020 10:14
Dat510 wrote: Fri Oct 02, 2020 9:34
-
Socket KTC 36 mm 6pt drive 1/2 inc. Ada yang tau buat ini mau buat ngebuka apa?
baru keinget punya juga 1. 12pt 36mm 1" square drive.
tempo hari berusaha buka mur bearing roda depan innova dan berakhir dengan G A G A L T O T A L.
20201002_170807.jpg
bengkok euy....
20201002_170902.jpg
You do not have the required permissions to view the files attached to this post.
yanuarra
Full Member of Mechanic Engineer
Posts: 4040Joined: Sat Dec 28, 2019 9:55Location: Jakarta
Post by yanuarra Fri Oct 02, 2020 10:22
Sliding handle merk apa itu mbah?
DOHC
Full Member of Mechanic Master
Posts: 27643Joined: Sat Jan 31, 2009 17:48Location: in engine bay with carbonfibre as roof
Post by DOHC Fri Oct 02, 2020 10:24
marmut wrote: Fri Oct 02, 2020 10:14 Dat510 wrote: Fri Oct 02, 2020 9:34
-
Socket KTC 36 mm 6pt drive 1/2 inc. Ada yang tau buat ini mau buat ngebuka apa?
baru keinget punya juga 1. 12pt 36mm 1" square drive.
tempo hari berusaha buka mur bearing roda depan innova dan berakhir dengan G A G A L T O T A L.
20201002_170807.jpg
bengkok euy....
20201002_170902.jpg
Jij salah pakai sliding T mbah
Harusnya jij pakai konci L
Sliding T buka baut chassis aj bengkok
numpang lewat aja....
marmut
New Member of Mechanic Master
Posts: 11865Joined: Wed Oct 16, 2013 6:27Location: tangerang selatan
Post by marmut Fri Oct 02, 2020 10:30
yanuarra wrote: Fri Oct 02, 2020 10:22
Sliding handle merk apa itu mbah?
merk
blesak . buatan tegal.
marmut
New Member of Mechanic Master
Posts: 11865Joined: Wed Oct 16, 2013 6:27Location: tangerang selatan
Post by marmut Fri Oct 02, 2020 10:32
DOHC wrote: Fri Oct 02, 2020 10:24
Jij salah pakai sliding T mbah
Harusnya jij pakai konci L
Sliding T buka baut chassis aj bengkok
ember.
Omnibus
New Member of Mechanic Master
Posts: 11781Joined: Tue Apr 08, 2008 10:12
Post by Omnibus Fri Oct 02, 2020 10:40
Dat510 wrote: Fri Oct 02, 2020 9:34
Ikut meramaikan dalam rangka percepatan thread Hand Tools menuju Part 3.
WhatsApp Image 2020-10-02 at 4.15.36 PM(1).jpeg
WhatsApp Image 2020-10-02 at 4.15.36 PM.jpeg
Socket KTC 36 mm 6pt drive 1/2 inc. Ada yang tau buat ini mau buat ngebuka apa?
yg tepat itu buat buka oil filter housing bmw m52/m54
ga perlu 3/4" krn cuma sekira 20 Nm mengencangkannya.
btw ktc euy .... maknyusssssss keren
Omnibus
New Member of Mechanic Master
Posts: 11781Joined: Tue Apr 08, 2008 10:12
Post by Omnibus Fri Oct 02, 2020 10:42
marmut wrote: Fri Oct 02, 2020 9:31
ternyata saya masih menyimpan sedikit dokumentasi saat saudara jack daniels sedang beraksi dengan dekko solder station-nya,
Mr.
jd200 gabut utak atik ECU LS400,
20200116_211428.jpg
sedikit penampakan dekko di sisi kanan atas,
20200116_203320.jpg
puyeng,
20200116_140240.jpg
wah office nya keren. nickname solderman sptnya cool?
Dat510
New Member of Mechanic Engineer
Posts: 796Joined: Sat Jan 03, 2015 12:58
Post by Dat510 Fri Oct 02, 2020 10:47
Omnibus wrote: Fri Oct 02, 2020 10:40 Dat510 wrote: Fri Oct 02, 2020 9:34
Ikut meramaikan dalam rangka percepatan thread Hand Tools menuju Part 3.
WhatsApp Image 2020-10-02 at 4.15.36 PM(1).jpeg
WhatsApp Image 2020-10-02 at 4.15.36 PM.jpeg
Socket KTC 36 mm 6pt drive 1/2 inc. Ada yang tau buat ini mau buat ngebuka apa?
yg tepat itu buat buka oil filter housing bmw m52/m54
ga perlu 3/4" krn cuma sekira 20 Nm mengencangkannya.
btw ktc euy .... maknyusssssss keren
Nahh ini dia jawaban yg benar. As expected secara mbah omni pernah punya mobil serupa.
25 Nm tepatnya mbah. Kenapa KTC, karena cuma nemu ini yg drive nya 1/2, brand lain termasuk tekiro 3/4.
Saya cuma punya Ratchet & L handle 1/2 jd males nambah lg yg 3/4 cuma buat accomodate 1 socket.
Omnibus
New Member of Mechanic Master
Posts: 11781Joined: Tue Apr 08, 2008 10:12
Post by Omnibus Fri Oct 02, 2020 10:55
Dat510 wrote: Fri Oct 02, 2020 10:47
ada yg ini juga om ... 36 mm khusus utk oil filter german cars. dan pakai 3/8" sq drive spy lebih elegant bentuknya
https://tokopedia.link/l3SNWtoNfab
Dat510
New Member of Mechanic Engineer
Posts: 796Joined: Sat Jan 03, 2015 12:58
Post by Dat510 Fri Oct 02, 2020 12:53
Wah nemu aja mbah, saya kemarin keyword nya langsung specific socket 36 mm jd ngga ketemu yg itu.
Tapi klopun ketemu kayanya saya tetep beli yg KTC, overkill ah pake stahlwille, wong montir juga biasanya pake kunci inggris. Wkwk
